Mô tả

Bộ chuyển đổi Modbus RTU/ASCII sang HART ICP DAS HRT-310-UTA CR

Features

  • Support HART Short/Long frame
  • Support HART Burst mode
  • Allow two HART Masters
  • Working in point-to-point or multi-drop HART mode
  • Connecting up to 15 HART modules
  • Support Modbus RTU and ASCII format
  • Support Modbus Slave mode
  • Support firmware update via Com Port
  • Support on-line replacement of HART devices
  • Support acquire Long Frame Address automatically
  • Provide LED indicators
  • Built-in Watchdog
  • DIN Rail or Wall Mounting

Introduction

The HRT-310-UTA Gateway is specially designed for the master device of HART protocol. It allows the Modbus master to access the HART devices. These HART devices may be a transmitter, an actuator and so forth. In addition, we also provide the software utility, HG_Tool, for module configuration and HART device diagnosis. By using these modules, users can integrate their HART devices into Modbus network easily and quickly.

Model HRT-710 HRT-310
Din Rail Installation Horizontal Upright
HART Signal Standard Enhanced send/receive signal
(For long distance comm.)
Loop Power No Support
(module provides +30V output)
Built-In Resistor 250 Ohm (1/4W) 250 Ohm (1W)

Applications

  • Industrial Automation
  • Factory Automation
  • Process Automation
  • Etc…

HRT-310-UTA, a HART master to Modbus slave gateway, is applied to integrate the information from these HART flow meters into the customer's HMI system. Through the HRT-310, all of the HART flow meters will be regarded as Modbus slave devices and the HMI system can use the built-in Modbus RTU communication to access these HART flow meters easily.

More than 250 HART device information needs to be integrated to surveillance center. In PC side, uses 3 pieces of PCI cards (VXC-148U, for 24 channels RS-485 expansion). I-2542A and I-2542B (RS-485 to Fiber) are used in every RS-485 channel to extend RS-485 communication distance. There are about 20 pieces of HRT-310-UTA modules used in every RS-485 channel with the different station ID. Through the structure, SCADA or HMI system can integrate all HART device information via Modbus protocol easily and quickly.

Specifications

COM Ports
Ports RS-232(3 wires) / RS-422 / RS-485
Baud Rate 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200
Protocol Modbus RTU / Modbus ASCII
HART
Ports 1
Device 2-wired or 4-wired HART devices
Topology Point to Point or Multi-Drop
Data Only Digital Data
Frame Type Short and Long Frame
Burst Mode Supported
Max. HART Device 15
Loop Resistor 250 Ω (1W) by Dip-Switch
Isolation UL1577 Spec.
Protocol 2-pin screwed terminal block
Loop Power Yes (module provides +30V output)
Power
Reverse Polarity Protection Power reverse polarity protection, Over-voltage brown-out protection
Input Range Unregulated +10 ~ +30 VDC
Consumption 3.5W (Max.)
Mechanical
Dimensions (mm) 25 x 116 x 120 (W x L x H)
Installation DIN-Rail (Upright)
Environment
Operating Temperature -40 ~ +75 °C
Storage Temperature -40 ~ +80 °C
Humidity 10% ~ 90% RH, Non-condensing

Download

Datasheet

Documents

Ordering Information

HRT-310-UTA     CR  Modbus RTU/ASCII to HART Gateway (RoHS) (for -40 ℃ application)

 

Đăng nhập
Đăng ký
Hotline: 0904251826
x